C&K systems System 238 Instrukcja Instalacji Strona 11
- Strona / 28
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SYSTEM 238 Installation Manual
11
Command Locations 0D - 0F: Receiver #1 Phone Number
Order in which the numbers will be dialed
Command Location 0D
(1) (2) (3) (4) (5) (6)
Command Location 0E
(1) (2) (3) (4) (5) (6)
Command Location 0F
(1) (2) (3) (4) (5) (6)
Command Locations 0D - 10
Command Location 0D: Receiver #1 Phone Number (digits 1 - 6)
Digit Positions (1) - (6):
0 - 9 = dialing digits
0 = dial tone detect
2 = * (DTMF dialing only, not used in pulse dialing)
3 = # (DTMF dialing only, not used in pulse dialing)
4 = end of number
5 = 5 second delay
(1) (2) (3) (4) (5) (6)
0D
E00000
Default Values
Digit (1) is dialed first.
You must place a 4 (EON) after the last digit to be dialed. Fill in
remaining positions with "0". The zeroes will not be dialed.
Command Location 0E: Receiver #1 Phone Number (digits 7 - 12)
0E
(1) (2) (3) (4) (5) (6)
000000
Default Values
Command Location 0F: Receiver #1 Phone Number (digits 13 - 18)
0F
(1) (2) (3) (4) (5) (6)
000000
Default Values
Command Location 10: Account Number 2
10
(1) (2) (3) (4) (5) (6)
000000
Default Values
Digit Positions (1) - (6): Account Number 2
Valid entries are 0 - F.
Entries 0 and A both transmit 10 pulses. The Account Number is right justified.
The last digit must be in Position (6). The SYSTEM 238 will ignore unused Digit Positions:
Digit Positions (1) - (3) in 3-digit accounts
Digit Positions (1) & (2) in 4-digit accounts
Fill left hand unused portions with any digit values. They will not be used by the system.
PROGRAMMING CONVERSIONS
Hexadecimal Value
Key Strokes
A
B
C
D
E
F
0
1
2
3
4
5
Account Number 2 is used in
conjunction with Receiver Number 2
- GENERAL INFORMATION 1
- POWER SUPPLY INFORMATION 1
- P/N 5-051-162-00 Rev K 1
- Table of Contents 2
- WIRING THE PANEL 3
- LOOP INPUTS 4
- TELEPHONE INTERFACE 4
- FACTORY SETTINGS 5
- PROGRAMMING OPTIONS 5
- KEYPAD SETUP 5
- SYSTEM START-UP 5
- PROGRAMMING THE PANEL 6
- PROGRAMMING the ALPHA KEYPAD 7
- ALPHAII Programming Template 7
- Command Locations 00 - 08 8
- Command Locations 09 and 0A 9
- Command Locations 0B and 0C 10
- Command Locations 0D - 10 11
- Command Locations 11 - 13 12
- Command Locations 14 - 16 13
- Command Locations 17 - 26 14
- Command Locations 27 - 29 15
- Command Location 2A and 2B 16
- Command Locations 2C and 2D 17
- Command Locations 2E and 2F 18
- 3034 = Loop 5 19
- Watchdog Indicator 20
- Command Location 0D 23
- Command Location 0E 23
- Command Location 0F 23
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa C&K systems System 238
(16 strony)EWM Sistemi per la saldatura manuali utente
La lista di EWM Sistemi per la saldatura prodotti contiene 14 manuali utenti per 7 modelli. Tutte le guide utenti pdf sono disponibili per essere scaricate o visionate online.
Komentarze do niniejszej Instrukcji